Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Everman
Gate repair in Everman, TX typically costs between $145 and $485, depending on whether you’re dealing with a sagging hinge, a heaving post, or a dead control board. Most hinge post resets and realignments are completed in a single visit, and we schedule Everman calls within one to two business days. If your gate is dragging the grass on W Enon Ave or swinging past the latch on Oak Grove Road, call us at (817) 961-9404 and we’ll put a live person on the line. The company that replaces the hinge but ignores the clay under the post hasn’t fixed your gate. We know the difference.
Why Ironworks Gate Co. Is Everman’s Preferred Gate Repair Company
We’re a gate repair company, full stop. Not a handyman service that also does gates, not a fence crew that swaps hardware as a side job. Since 1984, Ironworks Gate Co. has done nothing but build, hang, weld, and automate driveway gates. Victor Salinas leads our team with one directive: diagnose the cause, not the symptom, and stand behind the work in writing. That’s why our Gate Repair team carries the 90-Day Done Right Promise on every job in Everman. If it’s not right, we come back and make it right. No paperwork, no arguing.
Everman’s gates are different from what you’ll find in newer suburbs. Most were hung in the 1960s through early 1980s, on posts set 18 inches deep in Blackland Prairie clay that never stops moving. A tech who doesn’t know this soil will swap a hinge and call it done. We reset posts. We know that a gate off W Enon Ave behaves differently in March than it does in August, because the ground under it behaves differently. That local knowledge built our reputation here. Every call from Everman is answered by a live person, 24 hours a day, and every customer gets upfront pricing agreed before we turn the first bolt.
Our Gate Repair Services in Everman
Older gates fail in predictable ways, and we’ve structured our work around the failures we actually see in Everman’s neighborhoods near Enon, Oak Grove, and the blocks around Everman High School. Here’s what we do most.
Hinge & Post Repair
This is the most common gate repair we perform in Everman. The expansive clay under this city swells through wet springs and contracts through drought summers, heaving shallow footings and tilting posts out of plumb. A post leaning two degrees is enough to drag a chain-link gate through the grass. We pull the post, bore a full 30-inch footing, set it in concrete with rebar, and weld in new hinge barrels rated for the gate’s weight. Then we address the sag the post lean created. Fixing the soil side of the problem is what keeps the gate working through the next wet-dry cycle.
Gate Realignment
When a tubular-steel gate drops at the latch stile or swings past the strike, the frame has racked. In Everman, that racking is almost always driven by post movement underneath, not by the gate panel itself. We re-square the frame, correct the post alignment, and adjust the catch so the gate latches cleanly without a shim or a bungee cord. If you’ve been propping your gate shut with a cinder block, call us. That’s a realignment job, and it usually takes one visit.
Electric Gate Repair
Everman has a surprising number of electric gates hung with legacy LiftMaster and FAAC operators that predate UL 325 entrapment protection. Many of these still run, but their control boards are obsolete. When the board fails, you’re left with a gate that won’t move, won’t reverse, or won’t respond to the remote. We service these older units and can often retrofit modern photo-eyes and safety edges onto them, but when the board is beyond saving, we’ll tell you straight. A new operator on a solid old gate is frequently cheaper than nursing a 30-year-old board through another repair cycle.
Lock Repair
Locks on older Everman gates take constant abuse, especially on chain-link swing gates where the post has moved and the latch no longer lines up. We repair and replace gate locks, keypads, and access control hardware, and we make sure the latch works after the gate is realigned. A new lock on a misaligned gate is a wasted trip. We don’t do wasted trips.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Everman
We’re trained and equipped on nine gate-automation brands, including Linear, BFT, and Viking, as well as LiftMaster, FAAC, DoorKing, and others. For Everman homeowners, that means whatever is mounted on your post, we can diagnose it and fix it without hunting for parts across the Metroplex. We stock the boards, remotes, photo-eyes, and hinge hardware that older gates in this area actually use. No second visit because we had to order something.
Common Gate Repair Problems We See in Everman Homes
- Post lean from Blackland Prairie shrink-swell cycles. The same clay that moves foundations in Tarrant County moves gate posts, too. Shallow 1960s and 1970s footings heave in March and pull back in August, and the gate racks with every cycle. This is the single most common repair call in Everman.
- Worn hinge barrels on original equipment. Forty years of Texas sun, 100°F summers, and deferred maintenance burns through weld points and hinge barrels. When the barrel wallows out, the gate drops at the latch stile and won’t close without being lifted.
- Obsolete control boards on legacy operators. Many Everman automatic gates still run on boards that can’t accept modern safety sensors. When those boards fail, the gate is dead until you swap the board or replace the operator entirely. We’ll tell you which one makes sense.
- Drag-and-gap cycling on chain-link swing gates. The same gate will drag the ground in March after a wet winter, then swing wide of the strike in August after the clay dries and pulls the post back. It’s not two separate problems. It’s one shallow post oscillating between two failure modes, and the fix is a proper footer.
Pricing for Gate Repair in Everman, TX
We quote every job upfront, agreed before any work starts. Here’s what Everman homeowners can expect to pay for common repairs:
- Hinge barrel replacement: $145 - $225 per hinge, including weld and realignment.
- Post reset with new concrete footer: $285 - $485, depending on gate weight and access.
- Electric gate operator board repair or replacement: $190 - $420, parts included.
- Full gate realignment and latch correction: $175 - $310.
- Safety sensor retrofit (photo-eyes or edge sensors): $165 - $295.
We don’t pad these numbers. Your quote is written, the price is fixed before work begins, and the 90-Day Done Right Promise covers the fix. Active offers for Everman customers include $50 Off Any Repair Over $250, a Free Second Opinion on any written estimate, and an $89 Seasonal Tune-Up. Seniors and veterans always get a 5% discount.
We Also Serve Cities Near Everman
Our team covers Everman and the surrounding communities, including Cleburne, Itasca, Keene, and Joshua. If you’re just outside Everman’s city limits, we’ll still come take a look. Dispatch is coordinated from our Dallas-Fort Worth office, and crews serve Everman locally, so response times stay short.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Everman
Because your post is set in Blackland Prairie clay that never stays still. Spring rain swells the soil and heaves the post, lifting the gate off its line and dragging it through the grass. Summer drought dries the clay, the post pulls back the other way, and the gate swings past the catch. The real fix is a deeper post footing that reaches below the active shrink-swell zone. Call (817) 961-9404 for an exact assessment; estimates are free.
In many cases, yes. If the operator can accept modern photo-eyes and edge sensors, we can retrofit them and bring the unit up to current entrapment standards. If the control board is too old to support the upgrade, retrofitting costs more than the operator is worth. We’ll tell you honestly which path applies to your gate. Call (817) 961-9404 for an exact quote; estimates are free.
Look at the post, not the panel. If the post is out of plumb, or the gap between gate and post is wider at the top than the bottom, the post has moved. A bent panel usually shows a kink or bow in the steel itself. In Everman, we find the post is the culprit on most older gates. Call (817) 961-9404 and we’ll diagnose it honestly; estimates are free.
It’s both, and it’s dangerous. A gate that won’t reverse on contact or obstruction violates UL 325 safety standards and can injure a person or animal. It also usually means the safety sensors are failed or missing. Do not run the gate until this is corrected. Call (817) 961-9404 and we’ll get it fixed. This is not a do it yourself job; the entrapment forces on an automatic gate can be lethal.
In most Everman yards, keeping the swing gate is the better answer. We reset the post in a proper 30-inch footing, install new hinge barrels, and realign the gate. It’s faster and cheaper than converting to a slide gate, which requires new track and often a different operator setup. Slide gates make sense when space or grade make swinging impractical, but for most older Everman lots, a properly reset swing gate will last decades. Call (817) 961-9404 for a straight answer; estimates are free.
Most Everman calls are scheduled within one to two business days. Emergency failures, like a gate stuck open or an automatic gate that won’t respond, get priority. A live person answers our phone 24 hours a day, 7 days a week, and we’ll give you a straight answer about when we can be there. Call (817) 961-9404 and talk to us directly.
Call Ironworks Gate Co. for Gate Repair in Everman
If your gate drags, sags, won’t latch, or won’t move at all, call us at (817) 961-9404. We’ll give you a free estimate, a written price before work begins, and the 90-Day Done Right Promise on every job. Victor Salinas and the Ironworks team have been setting gates since 1984, and we’ll set yours so it stays set. Done right, and backed in writing. That’s the deal.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Everman and the Dallas-Fort Worth metro.