Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Installation for Cleburne Homeowners
A new gate in Cleburne typically takes one to two days to install, and our crews handle everything from digging the post footings to running the opener wiring and setting the hinges so the gate swings true. We’ve been hanging gates across Johnson County since 1984, and our work is backed by a written 90-Day Done Right Promise. If you’re tired of tightening sagging hinges or wrestling a gate that scrapes the driveway, call us at (817) 961-9404 and we’ll come measure the opening, walk the site with you, and put a firm price in writing before any work begins. Victor Salinas leads every installation, and the gate we hang for you is the same gate we’d hang on his own property.
What Our Gate Installation Service Includes
Every gate we install in Cleburne starts with the same question: what does this gate need to do for you, every single day, for the next twenty or thirty years. That shapes the steel thickness, the hinge style, the post depth, and the opener we recommend. Here’s what we handle under the full scope of our Gate Installation in Cleburne.
Driveway Gate
A driveway gate is the front line of your property, and in Cleburne it earns its keep in the July heat and the February freeze-thaw cycles that heave shallow footings. We set posts in concrete below the frost line, then hang the gate with adjustable hinges so it settles straight and stays straight. Most Cleburne driveway gates run 12 to 16 feet wide, and we quote those with the opener, safety edges, and a keypad included so you’re not nickel-and-dimed on the back end. For the Best Gate Installation in Cleburne, TX, we make sure everything is included upfront.
Pedestrian Gate
A pedestrian gate gives you daily foot access without opening the big driveway gate. We build these to match the driveway gate in material and finish, then set the post and hang the gate with a self-closing hinge and a lockable latch so it shuts behind you every time. If you have a sloped walkway, we’ll set the hinges so the gate clears the grade without dragging.
Sliding Gate
Sliding gates make sense on Cleburne properties with a steep driveway slope or a short setback where a swing gate won’t have room to arc. We pour a level concrete track with a steel V-rail, set the cantilever rollers on the gate frame, and test the gate under load so it rolls without binding. For wider openings, a cantilever slider keeps the gate off the ground entirely and survives gravel driveways better than a tracked one.
Swing Gate
A swing gate is the classic look here, especially on acreage lots and older Cleburne homes where a pair of leafs opening onto the pasture is the traditional entry. We build the frame from structural steel and hang each leaf on adjustable, greaseable hinges bolted through the post, not lag-screwed into it. The difference matters: a through-bolted hinge wears down over decades, not months.
Double Gate
A double gate, or bi-parting gate, is two leafs that meet in the middle, typically 16 to 24 feet of total opening. We set both posts, hang each leaf, and align the center so the two meet square with no gap and no droop, then sync the two openers to run in sequence. On a Cleburne slope we’ll add guide wheels to the outer corners so the leafs don’t sag under their own weight.
Security Gate
A security gate is built heavier: thicker steel, full-frame construction, and hardware that resists tampering. We’ve installed security gates for Cleburne homeowners with tool trailers, livestock, or just a long driveway they can’t see from the house. When you need Emergency Gate Installation in Cleburne, TX, we respond quickly. We’ll pair the gate with an access control keypad or a photocell safety beam, and every security gate we hang is built to the same Keystone Standard as everything else we install.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
We install and automate gates with BFT and LiftMaster openers most often on Cleburne properties, because those two brands hold up to the dust and the heat we get here. We keep their OEM components in the truck and our technicians train on their current control boards, so the opener we mount on your gate today is one we can tune and repair ten years from now.
We also work regularly with Linear and Viking operators, especially on heavier slide gates and ranch entries where the gate runs on duty cycle all day. Whether your gate ends up with one of those brands or any other make, we’ll wire it, set the limits, and test the safety loop until it runs like it grew there.
Signs You Need Gate Installation Right Now
- The gate scrapes the driveway on every swing. That scrape means the hinges have worn or the post has tipped, and the gate is now using the driveway as a load-bearing point. The frame is torquing every time it moves, and iron that torques cracks. Once a hinge weld pops, the leaf can drop without warning.
- You’ve welded the same hinge twice. A gate that needs the same repair twice in a year is telling you the original steel or hardware was undersized for the job. Installing a properly built gate now costs less than a third weld, a damaged opener, and a towing bill for someone’s car.
- The opener stops mid-travel or grinds on startup. That’s the motor fighting an unbalanced leaf, and every cycle shortens the life of the gearbox and the capacitor. When the gate is out of true, no opener brand will hold up. A properly installed gate runs so easily you can push it open with one hand.
- The posts wobble when you push on them. A wobbly post means the footing was too shallow or too small for that leaf’s weight and swing. Cleburne’s clay soil expands and contracts, and a shallow post will only keep tilting. The fix is a new, deeper footing and a properly set post, and it is not a job for a handyman with a post hole digger and a bag of Quikrete.
- You’re propping the gate open with a cinder block. A gate you can’t trust to stay shut is no gate at all. If you’re plugging the open position because the gate drifts or the opener keeps faulting, it is time to stop patching and start thinking about a gate that closes square and locks secure on its own.
Our Gate Installation Process - Step by Step
- 1
Site walk and measurement. We meet you at the gate line, measure the opening, check the grade, and talk through how you actually use the gate: vehicles, livestock, deliveries, kids on bikes. We’ll point out drainage, utility lines, and where the sun hits the keypad. This is where we find the problems before they become change orders.
- 2
Written quote, no obligation. You get a line-item price on paper: steel, post footings, hinges, opener, safety edges, keypad, labor. The number we quote is the number you pay unless you change the scope yourself. We do not start with a low guess and hand you a different bill at the end.
- 3
Footings and post setting. On install day, we dig below the frost line, set the posts in concrete, and let them cure square and plumb before any weight touches them. This is the slow, unseen part of gate installation that determines whether your gate still closes right in fifteen years. We don’t rush it.
- 4
Gate fabrication and hang. We build the frame, face it to your spec, mount the hinges, and hang the leaf. Then we open and close it a dozen times by hand before touching the opener, because the gate has to be right without the motor if it’s ever going to be right with one.
- 5
Opener install, safety testing, and walkthrough. We mount the opener, wire the safety edges and the keypad, set the travel limits, and load-test the system. Then Victor walks the job with you, shows you the manual release, sets your keypad codes, and leaves you a job you never have to think about again.
How Much Does Gate Installation Cost in Cleburne?
A single-leaf driveway gate in Cleburne, with a chain-driven opener, keypad, and safety edges, typically runs $3,800 to $6,500 installed. A double-leaf swing gate on a wider driveway starts around $6,000 and goes up with the steel gauge, the opener rating, and the finish. A heavy security gate or a full cantilever slider on a ranch entrance can push $9,000 to $15,000 or more. For a pedestrian gate alone, expect $1,200 to $2,800 depending on materials.
What moves the price in Cleburne is the post depth and the soil: clay that holds moisture means deeper footings and more concrete, and doing that right costs a little more up front and a lot less over the life of the gate. The steel gauge, the opener duty cycle, and the finish (powder coat versus bare steel you paint yourself) all move the number too. The best way to avoid overpaying is to get a line-item quote and compare it against what’s actually being built. A gate is not a gate: 14-gauge tubing and 11-gauge structural steel are two different animals. We’ll show you the difference on paper, and our estimates are free with no obligation.
Gate Installation Near Cleburne - Our Service Area
We install gates throughout Johnson and northern Hill County, and into Tarrant County when the job calls for it. Cleburne is home base, and we work regularly in Keene, Itasca, Joshua, Alvarado, and Gate Installation in Keene with the same crew and the same written guarantee. We also serve Crowley, Rendon, Everman, Benbrook, Mansfield, Forest Hill, and Kennedale. If you’re outside that ring, call us anyway and we’ll tell you straight whether the drive makes sense. And if you know someone a few towns over, we cover Gate Installation in Itasca as well, and our home page has the full scope of our gate work.
Serving Cleburne, TX - Our Local Coverage Area
We’re based in the Cleburne area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in Cleburne
Gate installation is the complete process of setting the post footings, building or delivering the gate leaf, hanging it on properly engineered hinges, and mounting the opener and safety systems. In Cleburne we build most gates on site so they fit the exact opening and slope, rather than forcing a cookie-cutter gate onto your driveway. We also offer our Gate Installation in Keene with the same custom approach. The install includes the concrete footings, the hardware, the opener, and the walkthrough at the end.
Most single-leaf driveway gates take one day to hang and a second day to finish the opener, safety edges, and keypad programming. A double gate or a heavy slider can take two to three days, especially if the footings need to cure before the leaf hangs. We schedule the job in a straight run so you’re not waiting a week between visits.
A single driveway gate with opener and keypad typically lands between $3,800 and $6,500 installed in Cleburne, while double gates and heavier security gates start around $6,000 and can go to $15,000 for a full ranch slider. The honest answer is that your gate’s size, the soil conditions at your gate line, and the opener’s duty cycle set the real number. Call (817) 961-9404 and we’ll come measure and put a firm price in writing, free.
Yes. We install and program BFT and LiftMaster openers on Cleburne gates every week, and we keep their OEM parts stocked for service callbacks. We also carry and install Linear and Viking for heavier slide gates. Whatever opener your gate needs, we mount it, wire it, and stand behind it under our 90-Day Done Right Promise.
If your gate failed and left your property unsecured, call us at (817) 961-9404 and a live person answers, day or night. For a true emergency we’ll give you a straight answer on when we can get there, and on installs we quote a schedule before you commit. A new gate is measured and built to order, so it’s not a same-day job, but securing a failed gate so it locks until the new one is ready is one we can usually start right away.
Every gate we install carries our written 90-Day Done Right Promise: if the gate isn’t right, we come back and make it right, no paperwork, no arguing. That sits on top of the manufacturer warranties on the opener and hardware. The promise is known internally as the Keystone Standard, and it applies to every job we complete.
Clear the gate line so we have room to work: move vehicles, trailers, and anything stored near the fence line back about ten feet. If you have irrigation lines near the gate, mark them or let us know, and we’ll hand-dig that section of the footing. You don’t need to be home the whole time, but it helps to be there for the first ten minutes so we can confirm the gate swing direction and keypad placement.
Schedule Your Gate Installation Service in Cleburne Today
Call (817) 961-9404 and you’ll talk to a real person, not a voicemail tree. We’ll set a time to come measure, walk the site with you, and give you a written price with no obligation. The estimate is free, the price is firm before the first bolt gets turned, and the gate we hang for you is one we’ll be proud to see still swinging square in twenty years. That’s how we’ve done it since 1984.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Cleburne since 1984.