Gate Motor & Opener in Cleburne - Written Price, Install Date Set

Trusted Gate Motor & Opener for Cleburne Homeowners

A gate motor or opener in Cleburne typically costs between $850 and $2,400 to replace, depending on the type of gate, the weight of the gate, and the brand of motor being installed. Most repair jobs, from a failed capacitor to a stripped gear, run $185 to $420 and are completed the same day. If your gate is stuck open, grinding, or refusing to respond to the remote, call Ironworks Gate Co. at (817) 961-9404 and we will send a technician to your driveway, usually the same afternoon.

Call (817) 961-9404

Victor Salinas started Ironworks Gate Co. in 1984, and in the 42 years since, we have opened and closed more Cleburne gates than we can count. Our technicians are trained and equipped on nine gate-automation brands, and every job we finish is protected by our written 90-Day Done Right Promise. A live person answers our phone 24 hours a day, 7 days a week. Not a voicemail, not an answering service. When your gate motor quits at 6 a.m. on a workday, you talk to a person who can help with our Emergency Gate Motor & Opener in Cleburne, TX.

What Our Gate Motor & Opener Service Includes

We work on the entire gate opening system: the motor, the control board, the arms, the hinges, the remote receivers, the safety sensors, and the wiring between them. A gate that will not open is rarely one problem. It is usually two or three small problems that have been feeding on each other for months. We find all of them in one visit.

Motor Installation

Best Gate Motor & Opener in Cleburne, TX means matching the motor to the gate, not just bolting on whatever is on the truck. We measure the gate’s weight, its swing or slide travel, and the condition of the hinges and track before we recommend a motor. Then we install the motor, the control board, and the safety edges, and we program the remotes and keypad to your exact setup. You get a written price before the first bolt is turned, and the installation is protected by the 90-Day Done Right Promise.

Motor Repair

Most gate motor failures in Cleburne come down to a handful of causes: a failed capacitor, a worn gear, a fried control board, water intrusion, or an electrical surge from a summer storm. We diagnose the actual fault before we touch a tool, then we repair it with OEM parts from the motor’s manufacturer. If the repair does not make financial sense compared to a replacement, we will tell you that plainly and quote both options. We do not patch a dying motor and call it fixed.

Linear Motor

Linear gate motors are the workhorses of slide gates, using a drive arm that pushes and pulls the gate along its track. When a linear motor starts to fail, you will usually hear it: a screech, a rattle, or a motor that runs but the gate inches along. We service and replace linear motors for every major brand, and we inspect the chain, the track, and the wheels at the same time. A new linear motor on a slide gate runs about $900 to $1,800 installed in Cleburne, depending on the gate’s length and weight.

Slide Motor

Slide gates are common on Cleburne acreage and long driveways off Highway 174 and Nolan River Road. The motor that runs them takes a beating: wind, rain, dust, and a gate that can weigh 800 pounds or more. We replace slide motors, service the limit switches, and align the chain and track so the gate rides smooth instead of bucking. If your slide gate has started stopping six inches short of the post, that is a limit-switch problem we can usually fix in under an hour.

Intercom Integration

Gate intercoms connect the driveway to the house, so a visitor can buzz in without you walking to the gate. A lot of Cleburne homes have older intercoms that work fine until they do not, and then no one can get in. We integrate gate motors with intercom systems, telephone entry systems, and newer cell-phone-based intercoms that let you see and talk to the person at your gate from anywhere. When the intercom and the motor are wired by the same company, the whole system finally behaves.

Battery Backup

A gate motor on a battery backup keeps working when Cleburne loses power, which matters if you have ever been stuck inside or outside your own driveway during a summer storm. We install battery backup systems that automatically take over when the grid goes down, then recharge when power returns. We also test the batteries we find on existing systems, because a battery that is five years old is a battery that is almost done. A battery backup installation typically runs $400 to $800 depending on the motor type.

Brands We Service for Gate Motor & Opener

We are certified on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters because a BFT motor has different programming menus than a Viking motor, and a technician who has worked on ten of them knows the short cuts. We have been inside hundreds of BFT control boards, and we keep their most common replacement parts on the truck. When you call about a BFT gate that will not open, we usually know the likely cause before we pull into your driveway.

We service a lot of Linear motors on older Cleburne slide gates, because Linear built them to last and people kept them for twenty years. We also work on plenty of Viking operators on the heavier estate gates, where the motor has to muscle a gate that weighs as much as a small car. Ghost Controls systems on newer residential gates are a frequent call for us too, often on gates installed by general contractors who did not dial in the force settings. Whether you have one of these brands or any other make, we can service it. If we cannot get the part, we will tell you that on the phone, not after we have charged you a diagnostic fee.

Signs You Need Gate Motor & Opener Right Now

• Your gate groans, grinds, or screeches when it moves. A healthy gate motor should be nearly silent. Grinding usually means a gear is wearing down, and once the gear strips completely, the motor runs but the gate does not move. This is a same-day repair in most cases, and catching it early saves you from replacing the whole motor.
• The gate stutters, stops mid-travel, or reverses for no reason. This is often a safety sensor that has drifted out of alignment or a force setting that was never tuned correctly. It is also a hazard if the gate reverses onto a car or a person. We recalibrate the sensors and set the force limits so the gate opens and closes all the way, every time.
• The remote works sometimes, from some angles, or only when you are right next to the gate. Weak or intermittent remote response is almost always a receiver or antenna issue, not a motor issue. We replace faulty receivers, reposition antennas, and reprogram remotes so the gate opens from your car where you actually wait, not from five feet away.
• Your keypad stopped accepting your code. Cleburne keypads sit in full sun all summer and take dust and rain all year. The circuit boards fail, the keypad membranes crack, and the programming resets. We replace keypads and program them to your existing openers, so everyone in the family has the same code on the same day.
• The motor runs but the gate barely moves. That is a classic sign of a failed capacitor, a slipping chain, or a motor that has lost its torque. Continuing to run the motor in this state burns it out completely. The fix is usually a $40 to $120 part and under an hour of labor, if we catch it before the motor cooks itself.

Our Gate Motor & Opener Process - Step by Step

We have been doing this long enough that our process is not a mystery. Here is exactly what happens when you call Ironworks Gate Co. about our Gate Motor & Opener in Cleburne.

1. 1
   You call, a person answers. No phone tree, no callback queue, no “leave a message and we will get back to you within 48 hours.” You talk to a live person who asks about your gate, your symptoms, and your schedule. We book a window that works for you, and we show up when we say we will.
2. 2
   We diagnose before we quote. Our technician arrives in a stocked truck, inspects the motor, the control board, the wiring, and the mechanical parts of the gate itself. We use a multimeter to test voltage at the motor and the board, because a motor that looks dead is often just underpowered. Then we explain what we found in plain English and give you a written price before any work starts.
3. 3
   We fix it in one visit. Because we carry OEM parts for nine major brands on the truck, most repairs and many full motor replacements are finished the same day. We do not leave your gate disassembled and your driveway unsecured while we “order a part.” If we do not have it, we tell you before we start, and we lock the gate manually so you are never stuck open.
4. 4
   We test everything twice. When the repair or installation is done, we run the gate through a full open-and-close cycle at least five times. We check the force settings, the safety sensors, the remotes, and the keypad. We watch for the small things: a gate that bounces at the close, a motor that runs hot, a remote with a weak signal. If it is not right, we fix it before we leave.
5. 5
   You get it in writing. Every job ends with a written summary of what we did, what we replaced, and the price you agreed to. You also get our 90-Day Done Right Promise in writing: if it is not right, we come back and make it right, no arguing, no paperwork, no exceptions. That is how we have kept Cleburne customers calling us back since 1984.

How Much Does Gate Motor & Opener Cost in Cleburne?

Gate Motor & Opener Near Cleburne - Our Service Area

We are based in Cleburne and we serve Johnson County and the surrounding communities: Itasca, Keene, Joshua, Alvarado, Crowley, Rendon, Everman, Benbrook, Mansfield, Forest Hill, and Kennedale. Most Cleburne calls get same-day or next-day service, and outlying areas are usually on our schedule within 48 hours. If you are in Itasca or Keene, you can read more about our Gate Motor & Opener in Itasca and Gate Motor & Opener in Keene service. We are also at home across all of Johnson County.

Frequently Asked Questions - Gate Motor & Opener in Cleburne

Schedule Your Gate Motor & Opener Service in Cleburne Today

If your gate will not open, grinds when it moves, or has not worked right since the last guy touched it, call Ironworks Gate Co. at (817) 961-9404. We will give you a free, written estimate, an honest answer about what your gate needs, and a fixed price before any work starts. A live person answers 24/7, and we stand behind everything with the 90-Day Done Right Promise. When you call, mention this page and ask about our $50 Off Any Repair Over $250, our free second opinion on any written estimate, and our 5% Senior and Veteran discount.

Written by Victor Salinas, Owner at Ironworks Gate Co., serving Cleburne and Johnson County since 1984.