Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Everman
When a gate motor quits in Everman, it’s rarely just the motor. More often it’s the clay under the post, the three-degree lean nobody noticed, or a control board that stopped being manufactured in 1994. Our Gate Motor & Opener team works on Everman driveways every week, and we’ve learned to look at the post footing before we ever touch the operator. If your gate is dragging, grinding, or dead at the keypad, call (817) 961-9404. We’ll send a technician who knows Everman’s soil as well as he knows a LiftMaster circuit board. And yes, a live person answers the phone. Twenty-four hours a day, seven days a week.
Why Ironworks Gate Co. Is Everman’s Preferred Gate Motor & Opener Company
Victor Salinas founded Ironworks Gate Co. in 1984. That matters in Everman because most of the gates we service here were hung around the same time, and we’ve watched the whole neighborhood age. We know a 1970s tubular steel swing gate off Enon Ave behaves differently than a 1990s slide gate near the Everman High School corridor. We know the post leaned after last spring’s rains. We know the capacitor in that old Viking board is probably original.
Homeowners here don’t ask for the cheapest fix. They ask whether the gate will still close in August, after the clay dries and pulls everything out of square. They ask whether the repair is guaranteed. Ours is, in writing. Every job carries the 90-Day Done Right Promise. If it isn’t right, we come back. No forms, no argument. That’s been the standard since 1984.
Our technicians are background-checked, uniformed, and trained on nine automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The brand on your gate is not a surprise to us. And dispatchers coordinate from our Dallas-Fort Worth office, so a crew is never far from Everman when a gate refuses to open on a Monday morning.
Our Gate Motor & Opener Services in Everman
Most of what we do in Everman falls into four categories. Here’s what each one looks like on the ground here, not in a catalog.
Motor Installation
Installing a new operator on an Everman gate almost always starts with the post, not the motor. If the post has leaned even a little, a new opener will bind, fault, and burn out early. We check the footing first, then recommend the right operator for the gate’s weight, swing direction, and how many times a day it cycles. A typical single-swing gate motor install in Everman runs $1,400 to $2,800, including the operator, mounting, limit setup, and final travel calibration. You’ll have the price in writing before a single bolt turns.
Motor Repair
Repair is where Everman’s older gates show their age. Capacitors dry out. Gears strip where the operator arm connects to a corroded weld point. And control boards, especially on 1980s-era openers, simply stop being made. We still repair what’s repairable, but we’ll tell you straight when a repair is throwing good money after bad. Most motor repairs in Everman run $225 to $650. We carry common boards, capacitors, limit switches, and arms on our trucks, which means most repairs happen in a single visit.
Linear Motor
Linear operators use a threaded steel shaft to move the gate, and Everman’s clay creates a distinct failure mode for them: binding. When the gate post heaves, even an eighth of an inch is enough to make the threaded shaft fight the gate instead of moving it. That overworks the motor, trips the current sensor, and eventually cooks the control board. We correct the post alignment first, then inspect the shaft, limit cams, and gearbox. Linear motor service in Everman typically lands between $250 and $700 depending on whether the shaft or gearbox needs replacement.
Slide Motor
Slide gates on Everman properties took off in the 1990s and early 2000s, and many are still running original equipment. The weak point here isn’t the motor. It’s the rack and pinion, especially where the gate’s weight shifted after years of soil movement. When the rack is misaligned, the pinion grinds, the motor strains, and the unit runs hot. A slide motor repair with rack realignment in Everman generally costs $300 to $800. If the motor itself is beyond saving, a full slide operator replacement runs $1,700 to $3,200 installed, depending on gate length and weight.
Battery Backup
Everman’s storm season knocks out power often enough that a battery backup is a practical upgrade, not a luxury. We add battery backup to existing LiftMaster and FAAC openers regularly, and in most cases you don’t need to replace the whole unit. The backup system keeps your gate operating through short outages and lets you open it manually after longer ones. Expect $350 to $800 for a quality battery backup installation on an existing operator in Everman.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Everman
We’re factory-trained on nine opener brands, but the ones we see most often on Everman driveways are LiftMaster, Linear, and the occasional Viking or Ghost Controls unit on newer installs. BFT show up too, especially on Italian-made slide operators from the early 2000s. We keep repair stock for all of them in our trucks, which means your Everman repair doesn’t wait on a parts shipment from Dallas. Whatever brand is on your gate, the correct fix happens on the first visit.
Common Gate Motor & Opener Problems We See in Everman Homes
- Clay-heaved posts that bind the operator. Everman’s Blackland Prairie soil swells in wet springs and shrinks in summer droughts. The hinge post drifts, the gate drags or misses the latch, and the operator faults repeatedly. We reset the post and footer first. The opener is usually fine.
- Obsolete control boards on 1960s to 1980s operators. Many original Everman gate openers outlived their own manufacturers. When the board dies and no replacement exists, we retrofit a modern LiftMaster or FAAC board if the motor is still strong. If the motor is tired too, replacement is the cheaper answer.
- Corroded operator arms at old weld points. A hundred degrees in August, year after year, accelerates rust where the operator arm bolts to the gate. That corrosion strips gears and bends arms. We cut out the old weld, reinforce the connection, and remount the arm correctly.
- Slide gate rack misalignment from soil movement. When the gate track or rack shifts, the pinion grinds against it. The motor runs hot, the current sensor trips, and the gate stops mid-travel. We realign the rack and inspect the pinion gear for wear before replacing anything motor-side.
Pricing for Gate Motor & Opener in Everman, TX
Here’s what Everman homeowners can expect to pay for common gate motor work, as of 2026:
- Motor repair: $225 to $650
- Control board replacement (retrofit): $400 to $900
- Single swing gate operator installation: $1,400 to $2,800
- Slide gate operator installation: $1,700 to $3,200
- Battery backup installation: $350 to $800
- Post reset with new concrete collar: $500 to $1,200
Soil conditions drive some of these numbers. A post that needs resetting costs more than a simple board swap, and Everman’s clay means more posts need resetting than in cities with stable soil. Every price is quoted and agreed before work starts. No surprises on the bill. Mention the $50 Off Any Repair Over $250 offer when you call (817) 961-9404. Seniors and veterans always get 5% off, on top of any other offer.
We Also Serve Cities Near Everman
Our Everman crews also cover Cleburne, Itasca, Keene, and Joshua, which means the same team that fixes a clay-racked gate on W Enon Ave can handle a slide gate south of town the same week. If you’re on the edge of Everman or just over the line, call us. Chances are we’re already in the area.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Everman
No. A new operator will not fix a post that moves with the seasons. The post itself is the problem. In Everman, the shrink-swell clay under older gates routinely heaves a post out of plumb by two to four degrees. In March the gate drags; by August, after the clay dries and pulls the post the other way, the gate overshoots the strike. We reset the post with a deeper concrete collar, then remount and recalibrate the operator. A motor replacement on top of a moving post just wears out another motor. Call (817) 961-9404 and we’ll check the post before we quote anything.
It depends on the motor’s condition, and we’ll tell you honestly which way saves money. If the motor windings and gearbox are still sound, a retrofit control board typically runs $400 to $900 in Everman, and that’s cheaper than a full replacement. If the motor is tired too, replacement is the better buy. A new single-swing operator installed on an Everman gate runs $1,400 to $2,800, and it comes with a modern board that will have parts available for another two decades. The old board won’t. We’ll give you both numbers before you decide.
Yes, where it matters. Current safety standards require proper entrapment protection on automated gates, including monitored photo eyes or edge sensors, and correct travel limits. A 1970s gate on original hardware almost never has any of that. When we install a new opener in Everman, we bring the gate up to code as part of the job. That includes adding safety edges or photo eyes where the gate could pinch or crush. It’s not an upsell. It’s the difference between a gate that closes and a gate that hurts someone.
The grinding tells you the rack and pinion have fallen out of alignment, and the hot motor means it’s been fighting that misalignment long enough to overwork itself. In Everman we usually trace the problem to the gate’s weight shifting as the soil moved under the track or wheels. The motor is often still salvageable once the rack is realigned, but continuing to run it hot will destroy the windings. Slide motor repair with rack realignment here runs $300 to $800. Call (817) 961-9404 and we’ll walk you through what we’re seeing, starting with a free estimate.
Yes, in most cases. If your LiftMaster opener is less than about 15 years old, we can usually add a compatible battery backup kit for $350 to $800 installed, and you keep the operator you already have. That covers you during Everman’s thunderstorm outages and lets you open the gate manually if the outage drags on. The only time we’d recommend replacing the whole unit instead is when the opener’s board or motor is near the end of its life anyway. We’ll tell you if that’s the case, and you’ll know the cost before we do anything.
Call Ironworks Gate Co. for Gate Motor & Opener Work in Everman
Your gate is the first thing you pass through when you come home and the thing that keeps the rest of the world out. It should close like it was hung yesterday. If it doesn’t, call (817) 961-9404. A live person answers, day or night. We’ll quote the work before we start it, stand behind it in writing, and be there when we say. That’s how we’ve done business since 1984, and it’s why Everman homeowners keep our number on the fridge.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Everman and the Dallas-Fort Worth area since 1984.