Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Everman
Gate installation in Everman usually runs $1,400 to $6,800 depending on the gate style, size, and whether we’re automating it. Most single swing gates on a standard residential lot land between $1,800 and $3,200 installed. The wildcard here isn’t the gate itself. It’s the dirt under it. Everman sits on Tarrant County’s Blackland Prairie shrink-swell clay, and that soil moves enough every year to tilt a poorly set post out of plumb by an inch or more. If you’re replacing a gate that’s been dragging or gaping for years, the footing is the first thing we check before we quote a single dollar. Call us at (817) 961-9404 and we’ll send a crew out to look at your gate, your posts, and your soil, then give you a written price before any work starts.
Why Ironworks Gate Co. Is Everman’s Preferred Gate Installation Company
We’ve spent 42 years in this trade and we’ve seen what Everman’s clay does to gate posts. A company from the limestone-underlaid western suburbs might set a post two feet deep and call it done. That won’t survive three seasons on black gumbo. We know to drill deeper, add crushed-gravel drainage, and brace the hinge post so it stays true through the wet-spring/drought-summer cycle. That’s the difference between a gate that still closes square in 2035 and one that’s dragging by next March.
Victor Salinas founded Ironworks Gate Co. on a simple rule: do the job right or don’t do it at all. Every crew we send to Everman is background-checked and uniformed, and every job carries our 90-Day Done Right Promise in writing. If it’s not right, we come back and make it right. No paperwork, no arguing. Most Everman jobs are completed in a single visit, and the price is settled before a single bolt is turned. A live person answers our phone 24 hours a day, seven days a week. Not a voicemail tree. Not an answering service. A person who can dispatch a crew to Everman the same day when you need it.
Our Gate Installation Services in Everman
Driveway Gate
A new driveway gate in Everman typically runs $2,200 to $6,800 depending on width, material, and automation. Most homes in Everman’s older blocks were built between the 1950s and early 1980s, and a lot of them still have the original chain-link or tubular steel gate. When we install a driveway gate here, we plan the post footings around the clay first and the gate second. A 12-foot double gate needs a different hinge-post strategy than a 10-foot single, and on Everman soil that strategy includes depth, drainage, and bracing.
Pedestrian Gate
Pedestrian gates in Everman are usually smaller jobs. $900 to $1,800 gets you a solid steel walk gate, properly hung, with a latch that actually catches in August when the clay has shifted the post a quarter inch. We set the post deep, pack it with gravel, and hang the gate so it’s true. Then we stand behind it for 90 days, in writing. If the gate sags on day 70 because the soil moved, we come back and fix it. That’s the Keystone Standard, and it applies to a 3-foot walk gate the same as it does to a 20-foot driveway gate.
Sliding Gate
Sliding gates work well on Everman lots where the driveway slopes or where a swing gate would arc into a tree or the house. A new sliding gate runs $2,800 to $6,000 installed, including the track and motor if you’re automating it. The most common failure we see on sliding gates in Everman isn’t the motor. It’s a track that’s been racked out of level because the concrete pad under it moved with the soil. We pour a deeper stem-wall footing for the track and set the operator post independently so the gate rolls true year-round.
Swing Gate
Swing gates are the classic Everman gate, and they’re the ones most affected by black gumbo clay. A new swing gate starts around $1,600 and runs up to $4,500 for a double gate with automation. The hinge post is everything. On a 1960s-era block near Enon Avenue, our crew replaced a chain-link swing gate that had been dragging after a wet March and swinging past its latch by August for years. We set the new hinge post in a 30-inch footing with crushed-gravel drainage, upgraded the worn hinges, and installed a LiftMaster gate operator with a safety photocell. That gate now closes true to the strike every month of the year.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Everman
We’re trained and equipped on nine gate-automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Whatever is on your driveway, we know it. In Everman we often see older BFT and Linear operators that builders installed twenty years ago and nobody has touched since. Those control boards fail, and when they do, homeowners get told the whole system needs replacing. Often it just needs the right board and a proper safety-sensor retrofit, which costs far less than a new operator. We keep common parts stocked in our service trucks, so most Everman jobs are finished in one trip. For deeper Gate Installation work, our specialists handle the full scope from footings to keypads.
Common Gate Installation Problems We See in Everman Homes
- Hinge posts tilting with the clay. Everman’s Blackland Prairie soil expands when wet and contracts when dry. A post set in a shallow footing moves seasonally, which makes a swing gate drag in spring and gap open in late summer. On new installations, we drill past the active clay layer into stable subsoil and add gravel drainage so the post doesn’t move.
- Rusted weld points on 1960s-1980s steel gates. Decades of DFW heat have blistered powder coat and hidden corrosion at the hinge-side welds on older tubular steel gates. When a weld fails, the gate drops and the hinges bind. We’ll tell you honestly whether a weld repair buys you five more years or whether replacement is the cheaper answer.
- Obsolete operator boards that won’t pair with modern remotes. Many Everman homes have operators from the 1990s or early 2000s. The control board fails, and the manufacturer no longer makes a replacement. Rather than throw away a good motor, we can often retrofit a modern aftermarket board with entrapment protection, which brings the operator up to UL 325 standards at a fraction of replacement cost.
- Operators without entrapment protection. A gate operator installed before UL 325 requirements can’t legally run in automatic mode without retrofitted photoelectric sensors and a reversing edge. If your Everman gate closes on a car or a grandchild, the liability is yours. We retrofit proper safety edges and photocells so the gate meets current standards and keeps operating automatically.
Pricing for Gate Installation in Everman, TX
Here’s what we quote in the Everman market right now. A basic single swing gate, steel, manual: $1,400 to $2,200. A double driveway swing gate with a BFT or LiftMaster operator: $3,800 to $6,800. A pedestrian gate: $900 to $1,800. A sliding driveway gate with motor and track: $2,800 to $6,000. Retrofitting an existing gate with a new operator and safety sensors: $1,200 to $2,600. Post reset and footing repair on an existing gate: $600 to $1,400. These are installed prices, quoted and agreed before any work starts. The one thing that changes a price mid-job is what we find when we dig. If your original post was set shallow in active clay, we’ll show you before we proceed. Senior and veteran customers get 5% off, always. And if you have a written estimate from another company, ask us for a free second opinion.
We Also Serve Cities Near Everman
Our crews cover all of Tarrant County and the surrounding area. Beyond Everman, we install gates in Cleburne, Itasca, Keene, and Joshua. The same crews, the same 90-Day Done Right Promise, and the same attention to soil conditions wherever we work. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and crews serve Everman locally.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Everman
Because your hinge post is moving, not your hinges. Everman’s Blackland Prairie clay swells with spring rain and shrinks in summer heat. A post set in a shallow footing tilts seasonally, which changes the gate’s arc by a half inch or more. Adjusting the hinges masks the symptom for a few weeks. The fix is digging the post out, setting it deeper into stable subsoil, adding gravel drainage, and re-hanging the gate. That’s a $600 to $1,400 job depending on the post and gate. Call (817) 961-9404 and we’ll diagnose it before we quote it.
Usually we can retrofit it, provided the gate itself is structurally sound. Chain-link is light and swing-friendly, so an older gate with good welds and a straight frame can take a modern operator with safety photocells and a reversing edge. If the welds at the hinge side are rusted through or the frame is racked, replacement is cheaper than band-aiding it. We’ll tell you which one you’re looking at and show you why before you spend a dollar.
No. Under UL 325, which has governed automatic gate operators since 2000, a gate can’t run in automatic mode without entrapment protection: photoelectric eyes or an equivalent non-contact sensor, plus a reversing mechanism. A 1970s operator doesn’t meet that standard. If it closes on a person or a vehicle, you’re liable. We can retrofit modern sensors and a reversing edge onto most older operators for $400 to $900, or install a new compliant operator if the old one is too far gone.
At least 30 inches, with a wider bell at the bottom and crushed gravel around the post for drainage. That’s deeper than the 18-24 inches you’ll get from a handyman or a big-box installer. On Everman’s black gumbo, 18 inches sits entirely within the active clay layer. The soil moves, the post moves, and the gate drags. We drill to 30 inches or deeper depending on the lot, and we check neighboring posts and fences to see what the soil has already done on your block. That’s the first diagnostic step on nearly every Everman gate installation.
The track has moved. Everman’s clay heaves the concrete pad or the track supports, the track gets a high spot or a bow, and the gate binds before it reaches the strike. Sometimes it’s a failed limit switch or a dead battery in the operator, but if the gate slows and stops at the same spot every time, it’s the track. We pour a deeper stem-wall footing for the track and set the operator post independently. That runs $800 to $2,000 depending on the length of the run, and it fixes the problem instead of just resetting the limit every spring. Get a free estimate for your Everman gate at (817) 961-9404.
Call Ironworks Gate Co. for Gate Installation in Everman
If your gate is dragging, gaping, rusted at the hinges, or still running a 30-year-old opener, call us. We’ll send a uniformed, background-checked technician to your Everman home, diagnose what’s actually wrong under the surface, and give you a written price before any work starts. That price is the price. We stand behind every job with our 90-Day Done Right Promise in writing, and Victor Salinas still answers for the work his crews do. Call (817) 961-9404 for a free estimate. A live person answers, 24 hours a day, seven days a week.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Everman and the Dallas-Fort Worth metroplex since 1984.