Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Benbrook
If your Benbrook gate won’t swing, drags across the driveway, or is slowly pulling its own post out of the ground, we can fix it. Ironworks Gate Co. repairs and rebuilds iron, steel, and pipe-and-rail gates all through Benbrook, from the acreage lots off Lakeside Drive to the ranchettes west toward the Tarrant County line. Most Gate Parts & Welding calls in Benbrook come down to two things: expansive clay that shoves posts out of plumb, and hardware that was never built for the span it’s carrying. We’ll correct both, and weld it so it stays corrected. Call (817) 961-9404 for a free estimate on any gate repair or custom welding job in Benbrook.
Why Ironworks Gate Co. Is Benbrook’s Preferred Gate Parts & Welding Company
Benbrook isn’t Keller or Colleyville. It’s a lakeside, semi-rural town where gates are heavy, driveways are long, and the ground underneath everything moves. Homeowners here don’t want a handyman who’ll weld a hinge one afternoon and vanish. They want someone who can look at a sagging 16-foot ranch gate and know the problem is in the footing, not just the hinge barrel. Our Gate Parts & Welding team has been doing exactly that for over 42 years.
We work in Benbrook regularly, and our dispatchers know the area well enough to route a tech from the Dallas-Fort Worth metro office to your driveway without getting lost in the backroads south of the lake. Reviews from Benbrook customers consistently mention two things: the tech arrived when promised, and the gate worked right the first time. Victor Salinas, our owner, holds every job to the 90-Day Done Right Promise. It’s written. If it isn’t right, we come back. No phone tree, no argument, no exception. A live person answers our line 24 hours a day, seven days a week, and the same crew that welds a new hinge in Benbrook this week will be the one standing behind it next month.
Our Gate Parts & Welding Services in Benbrook
Hinge Replacement
On Benbrook acreage, hinge replacement usually means retrofitting a heavier hinge than what the original builder installed. Many of these gates date to the 1970s and 1980s, hung on barrel hinges that were sized for a 10-foot gate, then asked to carry 14 or 16 feet. We cut the old hinge off clean, weld on heavy-duty barrel hinges with grease zerks, and set the gate square. A welded hinge replacement in Benbrook typically runs $220-$480 depending on gate weight and access.
Post Replacement
Few things in Benbrook hold a gate post straight. The black gumbo clay that lines the lake heaves and contracts through every wet/dry season, and an underscore-sized concrete footing becomes a pivot point. We excavate the old pier, sink a deeper footing with rebar, and reset the post plumb before hanging the gate. Most post replacements in Benbrook land between $380-$900, including concrete and cleanup. If the old post is rotted at the collar, the job costs more because we’re digging out more failing concrete.
Rail Repair
Pipe-and-rail farm gates are common all through the southern reach of Benbrook, and they crack at the top rail weld from years of sag and wind load. When a spring storm pushes through the open corridor along the lake, those cracks open fast. We cut out the cracked section, weld in a reinforced sleeve, and grind it smooth enough to keep horses and kids from catching on it. Rail repairs in Benbrook generally run $150-$350 per section.
Custom Welding
Some Benbrook properties need a gate that doesn’t exist in a catalog. A wider opening for a horse trailer, a matched section to lengthen an existing driveway gate, or a solar-panel mounting plate welded to a pipe frame. Our custom welding in Benbrook starts around $180 for small modifications and rises with the footprint of the work, quoted before we strike an arc. Every job is done by a uniformed, background-checked tech working in your driveway the way they’d work in their own mother’s.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Benbrook
You should not have to fire your gate opener because the hinge failed. We service the automation already on your Benbrook property, including Linear, Viking, and Ghost Controls operators, and our techs are trained across nine major brands. If you have a retrofit BFT on a 40-year-old steel gate, we can preserve the operator and fix the steel around it. We carry common hinge styles, latch hardware, and roller components on our trucks, so most Benbrook calls are completed in one visit. And if the opener itself needs attention, we’ll tune it while the gate is already off its hinges.
Common Gate Parts & Welding Problems We See in Benbrook Homes
- Clay heave tilting hinge posts. The shrink-swell clay around Lake Benbrook expands in spring and contracts in summer, moving post footings a fraction of an inch per season. Over three or four years that’s enough to bind hinges and crack frame welds. The fix is a deeper footing, not a bigger hinge.
- Rust-seized pivot pins on lake-adjacent properties. Moist air off the lake accelerates rust on untreated steel pins. When a hinge pin seizes, the opener keeps pulling until something bends or snaps. We see this regularly on gates that back up to Army Corps land.
- Sagging wide gates on undersized hinges. A 16-foot pipe gate puts enormous lever-arm stress on a pair of 4-inch barrel hinges. The gate sags, drags the caliche, and stresses the opener until its travel limits drift. We replace the hinge with a larger barrel and reset the frame.
- Cracked rail welds from storm-driven wind. Spring winds off the lake’s open corridor bend and fatigue the top rail weld on older ranch gates. Left alone, that crack migrates until the rail lets go. We weld in a sleeve before the gate comes down in the next storm.
Pricing for Gate Parts & Welding in Benbrook, TX
In Benbrook, you should have a real number before we start. A hinge replacement typically runs $220-$480. A full post replacement with new concrete and a deeper pier lands between $380-$900. Rail repair work is usually $150-$350 per section. Custom welding starts around $180 and is quoted by the job, not by the hour. Most Gate Parts & Welding work in Benbrook totals between $200 and $900, with the larger end covering wide ranch gates on problematic soil. We quote the price before any work starts, and that’s the price you pay. No surprise line items. Call (817) 961-9404 and we’ll give you the number over the phone or send a tech out for a free on-site estimate the same week.
We Also Serve Cities Near Benbrook
While this page is written for Gate Parts & Welding in Benbrook, our crews also cover Cleburne, Itasca, Keene, and Joshua. If you’re on the edge of Benbrook and aren’t sure whether you’re in our travel area, call us. Chances are, we’re already working nearby.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Benbrook
The black clay around your footing is the problem, not the post. In Benbrook, that clay shrinks and swells dramatically through the year, and every cycle torques the footing a little further out of plumb. Straightening the post without deepening the footing is like pumping a tire with a nail in it. A proper fix means removing the old concrete, digging a deeper pier, adding rebar, and resetting the post. That stops the seasonal creep. Call (817) 961-9404 and we’ll take a look at the footing without charging for the estimate.
Yes. We weld mounting plates and brackets directly onto pipe-and-rail frames for solar openers all the time in Benbrook’s lake corridor, where running mains power to the gate isn’t practical. We match the bracket to the gate’s tube diameter, orient it for the solar panel’s south-facing pitch, and weld the mount so the opener stays put through wind and clay movement. We work with Linear, Ghost Controls, and Viking solar-compatible operators, among others. The labor for a solar-opener weld-on bracket typically adds $180-$320 to the job.
For a 14- to 20-foot gate on expansive clay, we recommend heavy-duty barrel hinges with grease zerks, welded to the post, not bolted. The bigger barrel spreads the load over more bearing surface, the grease zerk lets you keep the pin lubricated against lake moisture, and the welded mount removes the bolt slop that accelerates hinge wear. On Benbrook’s clay, we pair that hinge with a deeper post footing. A hinge is only as good as the post it’s welded to.
Two likely causes. First, a hinge pin seized by rust from lake-adjacent moisture, which makes the opener work against friction until its force sensor triggers a reverse. Second, the post shifted out of plumb during the storm, moving the gate just enough to bind. Both are common in Benbrook’s lake corridor. We check both on the same visit: free the hinge or replace the pin, and re-plumb the post. Then we recalibrate the opener’s travel limits so it doesn’t fight itself. Call (817) 961-9404 and we’ll get it done.
Yes, and that’s the right fix in most cases. The gate frame is usually sound; what fails is the untreated steel pin inside the hinge barrel, rusted by lake air and seized under load. We cut the old pin out, ream the barrel, install a new hardened pin, and if the barrel itself is worn, we weld in a new one without touching the rest of the gate. For lakefront Benbrook properties, this is one of our most common calls, and the repair typically runs $220-$420 per hinge assembly.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Benbrook and surrounding Texas communities since 1984.
If your gate is sagging, seizing, or cracking, call us at (817) 961-9404. We’ll give you a straight answer and a fixed price before anything gets welded, cut, or poured. Ironworks Gate Co. has been standing behind its work for over 42 years, and we’ll stand behind yours in Benbrook too.