Ghost Controls Gate Parts & Welding Nationwide

Ghost Controls Gate Parts & Welding in Cleburne: What to Know First

Ghost Controls gate parts and welding in Cleburne usually run between $180 and $800, depending on whether we’re replacing a hinge, welding a cracked post bracket, or rebuilding a rail section. Most Ghost Controls part replacements are completed in a single visit, and we quote the full price before any work begins. As an independent Ghost Controls service provider, we stock or can source the parts your opener needs, and our welding shop handles the metalwork the manufacturer can’t ship in a box.

Call (817) 961-9404

This page is for Cleburne homeowners whose Ghost Controls opener still runs but whose gate itself has given up: sagging hinges, a post that’s leaning, a rail with a crack running through it. If you’ve got a Ghost Controls system doing the electrical work while the steel around it fails, call (817) 961-9404. A live person answers, day or night.

How Ghost Controls Products Fail - and How We Fix Them

• Hinge wear on the Ghost Controls gate arm brackets. We see this most often on the residential swing-arm kits installed on heavier Cleburne gates. The factory hinge brackets are cast aluminum, and after a few years of Johnson County wind loading, they develop hairline cracks at the mounting ears. We replace them with steel fabrications welded to match the original geometry. The arm doesn’t know the difference, but the gate stops wobbling.
• Gate post lean on Ghost Controls solar-powered setups. The Ghost Controls solar panel and battery box add weight to the post, and in Cleburne’s clay soil, posts shift after wet winters. We pull the post, re-set it in concrete with a wider footing, and re-weld the hinge plates to the new true position. If the post is too far gone, we replace it and match the weld pattern to the existing gate frame.
• Rail and track wear on Ghost Controls slide-gate kits. Ghost Controls slide systems use a chain-driven trolley, and when the chain tension is off, the gate drags and chews up the track. We realign the rail, repair or replace damaged sections, and set the chain tension the way Ghost Controls specifies. Then we weld reinforcement gussets where the rail mounts to the gate frame, which is where most aftermarket repairs fail a year later.
• Latch and lock misalignment after hinge replacement. This is the call we get a month after another company did the hinge work. The new hinges are slightly thicker than the originals, the gate now sits a quarter inch higher, and the latch doesn’t catch. We account for that before welding, not after. Our hinge replacements include adjusting or rebuilding the latch and lock point so the gate closes the way it’s supposed to.
• Aftermarket part incompatibility. Some online parts for Ghost Controls systems are reverse-engineered and out of tolerance by enough to cause binding. We’ve replaced aftermarket gate brackets that were a full eighth-inch off from the OEM spacing, which meant the opener motor was fighting the mount every cycle. When we can, we use genuine Ghost Controls parts; when we weld or fabricate, we match OEM dimensions precisely.

Our Ghost Controls Gate Parts & Welding Process

1. 1
   Call and describe the problem. You tell us what the gate is doing: sagging, grinding, not latching, pulling away from the post. A live person takes the call and schedules a time that works with you.
2. 2
   We inspect on site. Victor Salinas or one of our techs comes out, checks the hinges, posts, rail, rollers, and the Ghost Controls opener itself. We measure the wear and identify the real cause, not just the symptom.
3. 3
   We quote the job before any work starts. You get a written price for parts and labor. OEM Ghost Controls parts when available, quality fabrication when welding is the better fix. No surprises on the bill.
4. 4
   We do the work. Welding on site or in our shop, hinge replacement, post reset, rail repair, latch rebuilding. Most Ghost Controls parts and welding jobs are done in one visit.
5. 5
   We test the full system. The gate cycles open and closed under power. We check travel limits, chain or arm tension, and safety sensor alignment. The gate closes like the day it was hung.
6. 6
   You get the 90-Day Done Right Promise. Written guarantee. If it’s not right, we come back and make it right. No paperwork, no arguing.

What Ghost Controls Gate Parts & Welding Costs in Cleburne

Here’s what we typically see for Ghost Controls gate parts and welding in the Cleburne area:

• Single hinge replacement: $180-$320 per hinge, depending on gate weight and access.
• Gate post replacement with concrete reset: $400-$800, including removal of the old post, new steel post, concrete, and hinge re-welding.
• Rail or track repair with welding: $250-$600, depending on length of damaged section and whether we’re reinforcing in place or replacing a segment.
• Custom welding (bracket fabrication, gusset reinforcement, crack repair): $150-$450, quoted by the job after we see it.
• Latch and lock rebuild after hinge work: $120-$280, included in hinge replacement when needed.

What moves the price is gate weight, how far the post has moved, and whether the existing steel is worth welding or needs replacement. We quote everything before we start, and estimates are free. Call (817) 961-9404 for an exact number on your gate.

Why Cleburne Homeowners Call Ironworks Gate Co. for Ghost Controls Work

We’ve been serving Cleburne and Johnson County since 1984, and in that time we’ve welded more gate frames than we can count. When a Ghost Controls system needs parts or steel work, the opener is only half the job; the metal it’s bolted to matters just as much. Our techs are trained on Ghost Controls motors and limits, and we also service LiftMaster, Mighty Mule, and DoorKing, so if your system ever changes or you add a second gate, we handle that too.

Victor Salinas grew up in Cleburne, not far from Hulen Park, and learned welding and electrical systems at Hill College in Hillsboro. His father was a welder, so the smell of hot steel has never felt like work so much as something familiar. As he puts it: “If it swings, rolls, or latches, we can sort it out.” Every job gets the 90-Day Done Right Promise in writing. That’s how we’ve done it for 42 years, and that’s how we’ll do it for the next forty.

FAQs