Ghost Controls Gate Access Control Nationwide

Ghost Controls Gate Access Control in Cleburne: What to Know First

Ghost Controls gate access control in Cleburne is something we repair, replace, and upgrade regularly at Ironworks Gate Co., and most jobs are completed in a single visit. The honest price posture is this: a keypad or receiver replacement typically runs $180 to $340, while a full access control upgrade with phone entry or video intercom lands between $700 and $1,800 depending on the hardware and wiring already in place. We’re an independent Ghost Controls service provider, not a factory warranty center, but we work on these systems every week across Johnson County.

Call (817) 961-9404

If you own a Ghost Controls opener with a keypad, remote, or intercom that’s stopped responding, you’re in the right place. Call (817) 961-9404 and a live person answers, day or night.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls builds solid residential openers, but after enough Cleburne summers, certain access control components start misbehaving in predictable ways. Here’s what we see on service calls:

• AXS-1 and AXS-2 keypad dead zones after hard rains. The keypad housing traps moisture against the membrane contacts, especially on the west-facing side of a gate where afternoon storms blow in. We open the housing, clean the contact traces, and reseal with a dielectric barrier that holds up to Cleburne humidity. If the board’s already corroded, we swap in a new keypad rather than reviving a lost cause.
• Photo eye faults that aren’t the photo eye. On Ghost Controls TSS1 and TDS2 systems, the access control board throws a safety sensor error when the real culprit is a weak battery in the control box or a splice that’s gone green inside the conduit. We chase the actual cause before replacing parts, which saves owners money that other companies spend guessing with their credit card.
• Remote range fading to ten feet or less. The receiver antenna on older Ghost Controls units runs inside the metal control box, and over time the coax connection loosens. We relocate the antenna externally where possible and reterminate it, which typically restores range to the full distance the system had when it was new.
• Ghost Controls app and wireless keypad losing sync. The brand’s Wi-Fi bridge and wireless keypads communicate on a channel that gets crowded easily in neighborhoods with lots of security cameras and smart home gear. We re-pair the devices on a clean channel and shield the bridge from nearby interference, and the dropout issue usually disappears.
• Gate opening on its own or refusing to close. On TDS2 and TSS1 units with wireless edge sensors, a failing transmitter battery causes the board to behave like the gate has hit something when it hasn’t. We replace the edge sensor battery and recalibrate, which fixes the ghosting behavior without any board replacement.

Our Ghost Controls Gate Access Control Process

When you call Ironworks Gate Co. about a Ghost Controls access problem, here’s exactly what happens:

1. 1
   You call, a person answers. We ask what the gate is doing and what access device stopped working. Victor Salinas and the techs know Ghost Controls well enough that the first conversation usually points us at the right component before we ever drive out.
2. 2
   We arrive and test the system under load. Not just the keypad or remote that’s acting up, but the whole access chain: transformer, control board, receiver, safety edges, and the motor itself. A keypad that stopped working because a transformer is failing is a different job than a dead keypad.
3. 3
   We give you a written price before any work starts. We tell you what failed, what it costs to fix, and whether a factory Ghost Controls part or a quality aftermarket replacement makes sense for your situation. No surprises on the bill, ever.
4. 4
   We do the repair or replacement on the spot. Most Ghost Controls access control jobs are finished same day. We carry common Ghost Controls replacement components and compatible aftermarket parts on the truck.
5. 5
   We test everything with you standing there. Keypad codes, remotes, phone entry, safety reverse, auto-close timing. You watch the gate open and close and confirm the access devices work before we leave.
6. 6
   You get our 90-Day Done Right Promise in writing. If it wasn’t right, we come back and make it right. No paperwork, no arguing, no exceptions.

If it swings, rolls, or latches, we can sort it out.

What Ghost Controls Gate Access Control Costs in Cleburne

Here’s a straight answer on Cleburne pricing, because most companies won’t give you one over the phone:

What moves the price is labor time, whether we’re replacing one component or rewiring a whole access circuit, and whether factory Ghost Controls parts are still available for your model. We quote the price and you agree to it before any work starts. Call (817) 961-9404 for an exact quote. Estimates are free.

Why Cleburne Homeowners Call Ironworks Gate Co. for Ghost Controls Work

We’ve been serving Cleburne and Johnson County for over 42 years, and most of our Ghost Controls customers are people who’ve lived in the same home for twenty years or more. They’ve seen cheap repairs fail and they’re done with that. We service nine gate automation brands, including LiftMaster, Mighty Mule, and DoorKing, so when a Ghost Controls board isn’t economical to repair, we can tell you honestly whether a different used board or a compatible replacement makes more sense than spending more money on a discontinued part.

Every job is backed by our written 90-Day Done Right Promise. Background-checked, uniformed technicians do the work. And when you call, a live person answers. Not a voicemail, not an answering service.

Victor Salinas grew up in Cleburne, not far from Hulen Park, and learned welding and electrical work at Hill College in Hillsboro before spending decades fixing gates and motors across Johnson County. When it comes to a Ghost Controls system, he’s seen the failure patterns that a generalist handyman hasn’t.

FAQs